STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull. THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely BLUEPRINTING TUTORIAL layout the basic top shape of the compass. For each side of the compass box we add up .7 inches for each corner (.7 + .7 = 1.4 inches), This leaves 2.1 inches for the flat sides of the box. This measurement corresponds to the previous page when we measured the height of the box in the screencapture. The two numbers match up (more

or less) so we

DREDD (2012) ARMORED VEST PATTERNS 1 inch cotton webbing 4 inch x 1.5 inch leather panel (sewn over elastic straps) 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull. THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely BLUEPRINTING TUTORIAL layout the basic top shape of the compass. For each side of the compass box we add up .7 inches for each corner (.7 + .7 = 1.4 inches), This leaves 2.1 inches for the flat sides of the box. This measurement corresponds to the previous page when we measured the height of the box in the screencapture. The two numbers match up (more

or less) so we

DREDD (2012) ARMORED VEST PATTERNS 1 inch cotton webbing 4 inch x 1.5 inch leather panel (sewn over elastic straps) 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing DH2 - COSTUME AND PROP BUILDING BASICS - STUDIO CREATIONS Costume and Prop Building Basics - Still a work in progress - Costuming/Propmaking for the Beginner. Good advice to the first time costumer is to start small, learn some basic techniques, then advance into larger projects after you complete the first one.If you've never made a costume before, look towards a costuming project that uses everyday clothing items in the costume, and needs a single STORMTROOPER ARMOR KIT FOR SALE Looking For Stormtrooper Armor to buy? Licensed armor is HERE!!!!! Rubies Official Licensed Supreme Edition Stormtrooper Costume has finally hit the shelves!!! THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BODYCASTING

Plaster Bandaging the Back: Lets start plastering the model. Make sure the bodysuit is fitted correctly before you start. The groin area and the underarms are crucial parts.

BIKER SCOUT

The Helmet. The Biker Scout helmet is a very unique looking helmet. In this section we will discuss its design and the pre-made helmets and kits that are available for those fans that do not want to hand sculpt their own helmet.. The Scout helmet looks to have been custom sculpted by the crew over at ILM during the pre-production of "Jedi".

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

VACUUMFORMING

For vacuumforming, I use medium sized sheets of plastic sandwiched between two wooden frames and heated in my kitchen oven. These heated sheets of plastic will be pressed over a mold on a vacuumtable, outside of the oven. STYRENE, ABS, and PETG are the most common types of plastic sheets that I use to vacuumform parts with. DREDD - HELMET - STUDIO CREATIONS Here is a paraphrased quote from Robb Allsopp, Key Principal Costumer for the Dredd movie, about the paint colors used in making the helmets, "The helmet is gloss black, with gloss red trim. After painting, there was a lot of breakdown/weathering work. The exact color of red was a custom mix." (thanks to Jared Butler for acquiring

that quote.)

STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely

STUDIO CREATIONS

Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

MAKING BLUE PRINTS

Example - 7 foot tall cartoon character . 93mm on the photo should equal 7 feet (84 inches) in realife therefore 1mm = (7*12) / 93 = 0.9 1 millimeter on my photo will be drawn as 0.9 of an inch on my

blueprint.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The Helmet. The Biker Scout helmet is a very unique looking helmet. In this section we will discuss its design and the pre-made helmets and kits that are available for those fans that do not want to hand sculpt their own helmet.. The Scout helmet looks to have been custom sculpted by the crew over at ILM during the pre-production of "Jedi".

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BIKER SCOUT

Keep the holes at least 3/4 of an inch away from the edge of the armor. Place one 2X4 strip of sticky back velcro on the insides of the elbows, directly in between the strap holes. Thread the elastic bands though the holes and connect the velcro to velcro areas. Adjust for proper fit, if need be.

RIVETING BASICS

The thick end is the end with the little ball on it. this ball will cause the stem to flair out and hold the rivet in place. This is the correct way to push in the rivet. Push the rivet all the way in. Now grab the LOWER piece of plastic and push that UP on to the rivet through its hole also.

BIKER SCOUT

The Scout Blaster Unlike a lot of the weapons in the Star Wars movie, the Scout Blaster was a custom piece made by ILM. Normally the artisans at ILM would take existing weapons and modify them to be futuristic blasters, not so with the Biker Scout's weapon.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall. STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster. STORMTROOPER ARMOR KIT FOR SALE Looking For Stormtrooper Armor to buy? Licensed armor is HERE!!!!! Rubies Official Licensed Supreme Edition Stormtrooper Costume has finally hit the shelves!!! THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

THE DEFINITIVE HOW TO Welcome to the "Definitive How To" on making a Tusken Raider costume from the blockbuster Star Wars movies. In this website we will show you the Steps it took for us to build a Tusken Head piece, sew up the ragged robes and build their deadly Gadeffi (gaffi) stick. Sit back and enjoy the ride. Just so you know this costume took quite a while

to

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely DREDD (2012) ARMORED VEST PATTERNS 1 inch cotton webbing 4 inch x 1.5 inch leather panel (sewn over elastic straps) 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster. STORMTROOPER ARMOR KIT FOR SALE Looking For Stormtrooper Armor to buy? Licensed armor is HERE!!!!! Rubies Official Licensed Supreme Edition Stormtrooper Costume has finally hit the shelves!!! THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

THE DEFINITIVE HOW TO Welcome to the "Definitive How To" on making a Tusken Raider costume from the blockbuster Star Wars movies. In this website we will show you the Steps it took for us to build a Tusken Head piece, sew up the ragged robes and build their deadly Gadeffi (gaffi) stick. Sit back and enjoy the ride. Just so you know this costume took quite a while

to

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely DREDD (2012) ARMORED VEST PATTERNS 1 inch cotton webbing 4 inch x 1.5 inch leather panel (sewn over elastic straps) 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing sewing 2 inch webbing DH2 - COSTUME AND PROP BUILDING BASICS - STUDIO CREATIONS Costume and Prop Building Basics - Still a work in progress - Costuming/Propmaking for the Beginner. Good advice to the first time costumer is to start small, learn some basic techniques, then advance into larger projects after you complete the first one.If you've never made a costume before, look towards a costuming project that uses everyday clothing items in the costume, and needs a single

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE DEFINITIVE HOW TO Welcome to the "Definitive How To" on making a Tusken Raider costume from the blockbuster Star Wars movies. In this website we will show you the Steps it took for us to build a Tusken Head piece, sew up the ragged robes and build their deadly Gadeffi (gaffi) stick. Sit back and enjoy the ride. Just so you know this costume took quite a while

to

STORMTROOPER ARMOR KIT FOR SALE Looking For Stormtrooper Armor to buy? Licensed armor is HERE!!!!! Rubies Official Licensed Supreme Edition Stormtrooper Costume has finally hit the shelves!!!

BIKER SCOUT

The Helmet. The Biker Scout helmet is a very unique looking helmet. In this section we will discuss its design and the pre-made helmets and kits that are available for those fans that do not want to hand sculpt their own helmet.. The Scout helmet looks to have been custom sculpted by the crew over at ILM during the pre-production of "Jedi". DREDD - HELMET - STUDIO CREATIONS Here is a paraphrased quote from Robb Allsopp, Key Principal Costumer for the Dredd movie, about the paint colors used in making the helmets, "The helmet is gloss black, with gloss red trim. After painting, there was a lot of breakdown/weathering work. The exact color of red was a custom mix." (thanks to Jared Butler for acquiring

that quote.)

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

VACUUMFORMING

For vacuumforming, I use medium sized sheets of plastic sandwiched between two wooden frames and heated in my kitchen oven. These heated sheets of plastic will be pressed over a mold on a vacuumtable, outside of the oven. STYRENE, ABS, and PETG are the most common types of plastic sheets that I use to vacuumform parts with.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall. STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too. THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely

STUDIO CREATIONS

Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

BIKER SCOUT

The Cummerbund. The Cummerbund needs to be custom made to the wearers measurements. The Cummerbund veclros in the back and a 4 cm (1.5 or 2 inch) wide black strip of elastic creates a thong for the 'white groin flap' that is in the front. This groin strap goes under the crotch area, and velcros to the inside-back of the cummerbund.

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BIKER SCOUT

The Helmet. The Biker Scout helmet is a very unique looking helmet. In this section we will discuss its design and the pre-made helmets and kits that are available for those fans that do not want to hand sculpt their own helmet.. The Scout helmet looks to have been custom sculpted by the crew over at ILM during the pre-production of "Jedi". ZF1 - ASSEMBLY TUTORIAL - STUDIO CREATIONS ZF1 Assembly Tutorial. This tutorial will show you how to assemble a "Fhloston Paradise" ZF-1 replica as seen in the movie "The Fifth Element". The "Fhloston Paradise" model is the version that Zorg carried around the last half of the movie.

BIKER SCOUT

Keep the holes at least 3/4 of an inch away from the edge of the armor. Place one 2X4 strip of sticky back velcro on the insides of the elbows, directly in between the strap holes. Thread the elastic bands though the holes and connect the velcro to velcro areas. Adjust for proper fit, if need be.

RIVETING BASICS

The thick end is the end with the little ball on it. this ball will cause the stem to flair out and hold the rivet in place. This is the correct way to push in the rivet. Push the rivet all the way in. Now grab the LOWER piece of plastic and push that UP on to the rivet through its hole also.

BIKER SCOUT

The Scout Blaster Unlike a lot of the weapons in the Star Wars movie, the Scout Blaster was a custom piece made by ILM. Normally the artisans at ILM would take existing weapons and modify them to be futuristic blasters, not so with the Biker Scout's weapon.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall. STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too. THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely STUDIO CREATIONSNEWSCONTACTPROJECTSDH2 Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too. THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

The boxes are generally 9 cm wide, 6.5 cm tall and 2.5 cm deep. There is a diamond-esque shaped belt buckle box in the center, 2 beveled boxes on each side of that, and then 2 rectangular boxes that are on the outer ends of the utility belt. You will probably want to refer to our plaster casting , vacuumforming sections, and fiber-glassing to

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely

STUDIO CREATIONS

Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

BIKER SCOUT

The Cummerbund. The Cummerbund needs to be custom made to the wearers measurements. The Cummerbund veclros in the back and a 4 cm (1.5 or 2 inch) wide black strip of elastic creates a thong for the 'white groin flap' that is in the front. This groin strap goes under the crotch area, and velcros to the inside-back of the cummerbund.

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BIKER SCOUT

The Helmet. The Biker Scout helmet is a very unique looking helmet. In this section we will discuss its design and the pre-made helmets and kits that are available for those fans that do not want to hand sculpt their own helmet.. The Scout helmet looks to have been custom sculpted by the crew over at ILM during the pre-production of "Jedi". ZF1 - ASSEMBLY TUTORIAL - STUDIO CREATIONS ZF1 Assembly Tutorial. This tutorial will show you how to assemble a "Fhloston Paradise" ZF-1 replica as seen in the movie "The Fifth Element". The "Fhloston Paradise" model is the version that Zorg carried around the last half of the movie.

BIKER SCOUT

Keep the holes at least 3/4 of an inch away from the edge of the armor. Place one 2X4 strip of sticky back velcro on the insides of the elbows, directly in between the strap holes. Thread the elastic bands though the holes and connect the velcro to velcro areas. Adjust for proper fit, if need be.

RIVETING BASICS

The thick end is the end with the little ball on it. this ball will cause the stem to flair out and hold the rivet in place. This is the correct way to push in the rivet. Push the rivet all the way in. Now grab the LOWER piece of plastic and push that UP on to the rivet through its hole also.

BIKER SCOUT

The Scout Blaster Unlike a lot of the weapons in the Star Wars movie, the Scout Blaster was a custom piece made by ILM. Normally the artisans at ILM would take existing weapons and modify them to be futuristic blasters, not so with the Biker Scout's weapon.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall. STUDIO CREATIONSNEWSCONTACTPROJECTSDH2STUDIO CREATIONS PROTON PACKCREATION STUDIO YOUTUBEGEMEX GEL CREATIONS STUDIO Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BIKER SCOUT

The Cummerbund. The Cummerbund needs to be custom made to the wearers measurements. The Cummerbund veclros in the back and a 4 cm (1.5 or 2 inch) wide black strip of elastic creates a thong for the 'white groin flap' that is in the front. This groin strap goes under the crotch area, and velcros to the inside-back of the cummerbund. ZF1 - ASSEMBLY TUTORIAL - STUDIO CREATIONS ZF1 Assembly Tutorial. This tutorial will show you how to assemble a "Fhloston Paradise" ZF-1 replica as seen in the movie "The Fifth Element". The "Fhloston Paradise" model is the version that Zorg carried around the last half of the movie.

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall. STUDIO CREATIONSNEWSCONTACTPROJECTSDH2STUDIO CREATIONS PROTON PACKCREATION STUDIO YOUTUBEGEMEX GEL CREATIONS STUDIO Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

BIKER SCOUT

ASSEMBLED Scout Armor and Helmet Kit. ARMOR AND HELMET ARE ASSEMBLED, READY-TO-WEAR OUT OF THE BOX. Fan-made parts vacuum-formed from Gloss-White ABS plastic. Production time takes 30 days after payment is made. Email the propmaker SUPERKRATES your shipping info

VACUUMFORMING

Vacuumforming: Releasing the Plastic. 01 Unlock the clamps on the frame and pull the top frame off. Then pull the tape off. 02 Recycle the tape. If you are pulling multiple molds, try to recycle the tape by using it in the next frame pull.

RIVETS AND BUTTONS

CREATING A BODY CAST: In this section I will show you how to pull a bodycast of a human figure. The process is relatively simple yet very

dangerous.

THE HELMET - STUDIO CREATIONS The measurement of this commbox is 5.5cm wide x 9.5cm tall x 2cm deep (little deeper on the corners though due to the curve of the helmet). The Commbox is held in place on the helmet via a 1-inch long #6 threaded bolt. Take notice the wire antenna that protrudes out the top of the commbox. We drilled a small hole through the top of the commbox

BIKER SCOUT

BIKER SCOUT Introduction. Welcome to the Definitive Guide to making your very own Imperial Biker Scout Costume as seen in the Star Wars movie, Return of the Jedi.We'll discuss in depth the armor,cloth parts, helmet and blaster.

BIKER SCOUT

The Cummerbund. The Cummerbund needs to be custom made to the wearers measurements. The Cummerbund veclros in the back and a 4 cm (1.5 or 2 inch) wide black strip of elastic creates a thong for the 'white groin flap' that is in the front. This groin strap goes under the crotch area, and velcros to the inside-back of the cummerbund. ZF1 - ASSEMBLY TUTORIAL - STUDIO CREATIONS ZF1 Assembly Tutorial. This tutorial will show you how to assemble a "Fhloston Paradise" ZF-1 replica as seen in the movie "The Fifth Element". The "Fhloston Paradise" model is the version that Zorg carried around the last half of the movie.

PLASTER MOLD MAKING

Plaster Mold Making. Okay Smatter-Brains, with the sculpting finished we need to pull a negative cast of the head so that we can make a latex skin. To do this we need to pour liquid plaster over the head and let it dry. You should do this plaster cast in two halves, a Front

and a Back.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall.

STUDIO CREATIONS

Studio Creations is a multi-faceted creative group that specializes in

Film and Video.

DH2 - DEFINITIVE HOW-TO - COSTUME AND PROPMAKING TUTORIALS DH2: RANDOM BLOG. Time Management and Costuming/Cosplay. A Costume or Cosplay Project is very labor and time intensive. Making Checklists, Utilizing Calendars, Setting up 'costume work' schedules, and organizing your work area can all help you in achieving better project

time flow.

MAKING BLUE PRINTS

Example - 7 foot tall cartoon character . 93mm on the photo should equal 7 feet (84 inches) in realife therefore 1mm = (7*12) / 93 = 0.9 1 millimeter on my photo will be drawn as 0.9 of an inch on my

blueprint.

HOW TO BUILD A STORMTROOPER COSTUME That's right , this website will show you how to build a stormtrooper costume from the ground-up. Everything from making a bodycast of yourself to sculpting out the parts correctly, and then pulling vacuumformed plastic for the final pieces. Its' all right here. So sit back and start reading, and dont forget to print out these pages too.

ENDOR REBEL SOLDIER

There is a 61 cm (24 inch) long slit is sewn up the bottom-back of the trench coat, allowing for better maneuverability while wearing the coat. (pictures showing this slit will be posted soon) Add two pockets to the trench coat (shown in highlighted area A). These pockets are approximately 15.3 cm (6 inch) wide and 22.8 cm (9 inch) tall.

TUSKEN RAIDER

The Bandoliers The ILM Screen-used Bandoliers were actually World War 2 Enfield .308 ammo bandoliers used by the Allied forces. Prior to 2005, costumers could purchase these online/offline at various Army-Navy Supply stores for about $50.00 each, no days, they are tough

to find.

BIKER SCOUT

The kneepad for the Biker Scout is more of an overall cube shape than anything. It has these odd looking ridges cut into edges of the facets of the kneepad. The top of the kneepad has a rounded look to it due to the 3 beveled surfaces. The bottom of the kneepads have a slight outward curve along the edge, they are not supposed to be completely

DREDD (2012)

The movie's name is DREDD so the costume designer, Michael O'Connor, got approval on the design of Judge Dredd's costume first, before moving on to the other Judge Costumes. This means Judge Dredd's costume is the Standard. All other Judge costumes are based around Dredd's look. The links in the navigation bar above go into detail on all the parts of a Judge's costume. DREDD - HELMET - STUDIO CREATIONS Here is a paraphrased quote from Robb Allsopp, Key Principal Costumer for the Dredd movie, about the paint colors used in making the helmets, "The helmet is gloss black, with gloss red trim. After painting, there was a lot of breakdown/weathering work. The exact color of red was a custom mix." (thanks to Jared Butler for acquiring

that quote.)

TUSKEN RAIDER

The Robes. Getting the Tusken Raider robe sewing pattern to look right took a few times of Trial and Error. What we came up with as a solution to the BAGGY look of

Costume How-To

Projects

Contact