KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of LIMP MASS LOADED VINYL BARRIER KNM mass loaded vinyl barrier is used for enclosing noise sources, suspended between equipment and quiet areas, or lagged to the equipment casing. KNM-AL limp mass barrier material adds a layer of reinforced aluminum foil facing on one side increased mechanical

strength,

WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

KSCH | LOW PROFILE DECK-SUSPENDED CEILING HANGER KSCH offers unprecedented flexibility for isolated ceiling design. A single hanger design can be adapted to any isolated ceiling project. Patent No. 7,028,432 B2. 1" deflection spring performance in a narrow 3 1/2" airspace. Hanger configurations easily adapt to different deck heights. Attach directly to deck or slide into Unistrut® for easy ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of LIMP MASS LOADED VINYL BARRIER KNM mass loaded vinyl barrier is used for enclosing noise sources, suspended between equipment and quiet areas, or lagged to the equipment casing. KNM-AL limp mass barrier material adds a layer of reinforced aluminum foil facing on one side increased mechanical

strength,

WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

KSCH | LOW PROFILE DECK-SUSPENDED CEILING HANGER KSCH offers unprecedented flexibility for isolated ceiling design. A single hanger design can be adapted to any isolated ceiling project. Patent No. 7,028,432 B2. 1" deflection spring performance in a narrow 3 1/2" airspace. Hanger configurations easily adapt to different deck heights. Attach directly to deck or slide into Unistrut® for easy ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board.

SEISMIC RESTRAINT

TITAN Modular Seismic and Wind Restraint Vibration Isolator. TITAN is a modular seismic and wind restraint vibration isolator engineered to meet the latest building codes. TITAN is recommended for equipment mounted on a structural frame or concrete inertia base where the KINFLEX | FLEXIBLE CONNECTORS KINFLEX Flexible Connectors prevent stresses due to expansion and contraction, isolate against the transfer of noise and vibration, and compensate for misalignment. RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control ROOF CURBS | KINETICS NOISE CONTROL Kinetics roof curb isolation systems (ASHRAE type D) are specifically designed for curb-supported rooftop equipment. Kinetics In Curb Acoustical Treatments control breakout noise from equipment fans and compressors into the space below. NOISEBLOCK™ BARRIER WALLS NOISEBLOCK™ barrier wall systems are a cost effective solution to limit oil and gas midstream compressor noise. Noise from loading docks, traveling motorists on major highways/interstates, airport areas, and railways are effectively reduced using Kinetics reflective or absorptive barrier wall systems. ROOF CURB VIBRATION ISOLATION RAIL KSR 2.0 vibration isolation rails are specifically designed and engineered for use as a noise and vibration isolation system for roof curb-mounted mechanical equipment. KSR 2.0 equipment isolation rails are compatible with most roof-supported equipment and standard sheet metal roof curbs where the wood nailer is located under the top flange LIGHT DUTY EQUIPMENT ISOLATION RAIL Description. KINETICS LDR light duty rail isolation system is a low-cost solution designed to isolate residential style condensing units and other light weight equipment (small fans, mini split systems, etc.). LDR eliminates vibration from penetrating into the structure and occupants below. Standard LDR isolation system orders

will include four

KSM | STUD WALL ISOLATION PAD Apply KSM along the bottom and/or top plates of a stud wall wherever acoustical isolation is required to maintain a fully effective sound rated assembly. Manufactured from 1" thick KIP material. Anchor isolation bushing and load plate included. Accepts up to 3/8" anchor. Custom sizes/capacities available. ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

SR FLOORBOARD

Kinetics SR Floorboard is a unique sound underlayment material which substantially reduces sound transmission through hard surface floor

systems.

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. ROOF CURB VIBRATION ISOLATION RAIL KSR 2.0 vibration isolation rails are specifically designed and engineered for use as a noise and vibration isolation system for roof curb-mounted mechanical equipment. KSR 2.0 equipment isolation rails are compatible with most roof-supported equipment and standard sheet metal roof curbs where the wood nailer is located under the top flange KSCH | LOW PROFILE DECK-SUSPENDED CEILING HANGER KSCH offers unprecedented flexibility for isolated ceiling design. A single hanger design can be adapted to any isolated ceiling project. Patent No. 7,028,432 B2. 1" deflection spring performance in a narrow 3 1/2" airspace. Hanger configurations easily adapt to different deck heights. Attach directly to deck or slide into Unistrut® for easy KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

SR FLOORBOARD

Kinetics SR Floorboard is a unique sound underlayment material which substantially reduces sound transmission through hard surface floor

systems.

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. ROOF CURB VIBRATION ISOLATION RAIL KSR 2.0 vibration isolation rails are specifically designed and engineered for use as a noise and vibration isolation system for roof curb-mounted mechanical equipment. KSR 2.0 equipment isolation rails are compatible with most roof-supported equipment and standard sheet metal roof curbs where the wood nailer is located under the top flange KSCH | LOW PROFILE DECK-SUSPENDED CEILING HANGER KSCH offers unprecedented flexibility for isolated ceiling design. A single hanger design can be adapted to any isolated ceiling project. Patent No. 7,028,432 B2. 1" deflection spring performance in a narrow 3 1/2" airspace. Hanger configurations easily adapt to different deck heights. Attach directly to deck or slide into Unistrut® for easy

SEISMIC RESTRAINT

TITAN Modular Seismic and Wind Restraint Vibration Isolator. TITAN is a modular seismic and wind restraint vibration isolator engineered to meet the latest building codes. TITAN is recommended for equipment mounted on a structural frame or concrete inertia base where the

NOISEBLOCK™

Positive Displacement Vacuum Blowers. Kinetics NOISEBLOCK™ barrier and structural support steel wall system designed for hurricane force winds mounted on raised foundations offering proper airflow, maximum noise control and maintenance access at a large liquid natural gas

terminal.

KINFLEX | FLEXIBLE CONNECTORS Flexible Piping Connectors. KINFLEX Flexible Connectors prevent stresses due to expansion and contraction, isolate against the transfer of noise and vibration, and compensate for misalignment. RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control ROOF CURBS | KINETICS NOISE CONTROL Kinetics roof curb isolation systems (ASHRAE type D) are specifically designed for curb-supported rooftop equipment. Kinetics In Curb Acoustical Treatments control breakout noise from equipment fans and compressors into the space below. NOISEBLOCK™ BARRIER WALLS NOISEBLOCK™ barrier wall systems are a cost effective solution to limit oil and gas midstream compressor noise. Noise from loading docks, traveling motorists on major highways/interstates, airport areas, and railways are effectively reduced using Kinetics reflective or absorptive barrier wall systems. KSM | STUD WALL ISOLATION PAD Apply KSM along the bottom and/or top plates of a stud wall wherever acoustical isolation is required to maintain a fully effective sound rated assembly. Manufactured from 1" thick KIP material. Anchor isolation bushing and load plate included. Accepts up to 3/8" anchor. Custom sizes/capacities available. ROOF CURB VIBRATION ISOLATION RAIL KSR 2.0 vibration isolation rails are specifically designed and engineered for use as a noise and vibration isolation system for roof curb-mounted mechanical equipment. KSR 2.0 equipment isolation rails are compatible with most roof-supported equipment and standard sheet metal roof curbs where the wood nailer is located under the top flange ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of

SR FLOORBOARD

Kinetics SR Floorboard is a unique sound underlayment material which substantially reduces sound transmission through hard surface floor

systems.

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of

SR FLOORBOARD

Kinetics SR Floorboard is a unique sound underlayment material which substantially reduces sound transmission through hard surface floor

systems.

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board.

SEISMIC RESTRAINT

TITAN Modular Seismic and Wind Restraint Vibration Isolator. TITAN is a modular seismic and wind restraint vibration isolator engineered to meet the latest building codes. TITAN is recommended for equipment mounted on a structural frame or concrete inertia base where the KINFLEX | FLEXIBLE CONNECTORS KINFLEX Flexible Connectors prevent stresses due to expansion and contraction, isolate against the transfer of noise and vibration, and compensate for misalignment. ROOF CURBS | KINETICS NOISE CONTROL Kinetics roof curb isolation systems (ASHRAE type D) are specifically designed for curb-supported rooftop equipment. Kinetics In Curb Acoustical Treatments control breakout noise from equipment fans and compressors into the space below. NOISEBLOCK™ BARRIER WALLS NOISEBLOCK™ barrier wall systems are a cost effective solution to limit oil and gas midstream compressor noise. Noise from loading docks, traveling motorists on major highways/interstates, airport areas, and railways are effectively reduced using Kinetics reflective or absorptive barrier wall systems. ROOF CURB VIBRATION ISOLATION RAIL KSR 2.0 vibration isolation rails are specifically designed and engineered for use as a noise and vibration isolation system for roof curb-mounted mechanical equipment. KSR 2.0 equipment isolation rails are compatible with most roof-supported equipment and standard sheet metal roof curbs where the wood nailer is located under the top flange LIGHT DUTY EQUIPMENT ISOLATION RAIL Description. KINETICS LDR light duty rail isolation system is a low-cost solution designed to isolate residential style condensing units and other light weight equipment (small fans, mini split systems, etc.). LDR eliminates vibration from penetrating into the structure and occupants below. Standard LDR isolation system orders

will include four

KSCH | LOW PROFILE DECK-SUSPENDED CEILING HANGER KSCH offers unprecedented flexibility for isolated ceiling design. A single hanger design can be adapted to any isolated ceiling project. Patent No. 7,028,432 B2. 1" deflection spring performance in a narrow 3 1/2" airspace. Hanger configurations easily adapt to different deck heights. Attach directly to deck or slide into Unistrut® for easy KSM | STUD WALL ISOLATION PAD Apply KSM along the bottom and/or top plates of a stud wall wherever acoustical isolation is required to maintain a fully effective sound rated assembly. Manufactured from 1" thick KIP material. Anchor isolation bushing and load plate included. Accepts up to 3/8" anchor. Custom sizes/capacities available. SPRING VIBRATION ISOLATION HANGER Kinetics SH Vibration Isolation Hangers are designed to reduce the transmission of vibration and noise produced by suspended mechanical equipment, in-line and exhaust fans, ductwork, piping. SH Hangers incorporate a high deflection color-coded spring element, a No-Short spring cap, and noise isolation pad, assembled into a stamped or welded hanger bracket. ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control PERIMETER ACCESSORY PRODUCTS Perimeter Accessory Products noise control products. Resources. NOISE CONTROL BUILDING MATERIALS. NCBM HOME; PRODUCTS ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

SEISMIC ROOFTOP PIPE STANDS Application. KSPS stands stabilize piping by hard-clamping the piping to an adjustable steel mounting plate on the stand. This connection provides the necessary support the piping needs to act as a stand-alone support/restraint component; when used in accordance with MSS SP-69 table 3. KSPS stands can be used inside a structure or on

the roof top.

MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. WOOD-FRAMED CEILING HANGER Secured to wood-frame construction (e.g., joists, trusses), ICW incorporates a one-inch (1") rated deflection spring in series with a neoprene cup to resiliently support one or KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control PERIMETER ACCESSORY PRODUCTS Perimeter Accessory Products noise control products. Resources. NOISE CONTROL BUILDING MATERIALS. NCBM HOME; PRODUCTS ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

SEISMIC ROOFTOP PIPE STANDS Application. KSPS stands stabilize piping by hard-clamping the piping to an adjustable steel mounting plate on the stand. This connection provides the necessary support the piping needs to act as a stand-alone support/restraint component; when used in accordance with MSS SP-69 table 3. KSPS stands can be used inside a structure or on

the roof top.

MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. WOOD-FRAMED CEILING HANGER Secured to wood-frame construction (e.g., joists, trusses), ICW incorporates a one-inch (1") rated deflection spring in series with a neoprene cup to resiliently support one or PERIMETER ACCESSORY PRODUCTS Perimeter Accessory Products noise control products. Resources. NOISE CONTROL BUILDING MATERIALS. NCBM HOME; PRODUCTS KINFLEX | FLEXIBLE CONNECTORS KINFLEX Flexible Connectors prevent stresses due to expansion and contraction, isolate against the transfer of noise and vibration, and compensate for misalignment. SEISMIC ROOFTOP PIPE STANDS Application. KSPS stands stabilize piping by hard-clamping the piping to an adjustable steel mounting plate on the stand. This connection provides the necessary support the piping needs to act as a stand-alone support/restraint component; when used in accordance with MSS SP-69 table 3. KSPS stands can be used inside a structure or on

the roof top.

UNIBRACE - KINETICS NOISE CONTROL UniBrace is series of isolators that enable designers to decouple a multitude of miscellaneous items that can arise in any construction

project.

PICADO | ACOUSTICAL WOOD COLLECTION Picado is one of four distinctive patterns for sound absorption in The Acoustical Wood Collection. Alto. Picado. Sereno. TAD Revealed. These patterns enable designers to create beautiful auditoriums, atriums, conference rooms, courthouses, student centers or other areas where finished wood is desired and acoustical comfort is needed. LIGHT DUTY EQUIPMENT ISOLATION RAIL Description. KINETICS LDR light duty rail isolation system is a low-cost solution designed to isolate residential style condensing units and other light weight equipment (small fans, mini split systems, etc.). LDR eliminates vibration from penetrating into the structure and occupants below. Standard LDR isolation system orders

will include four

S4 | WIPEABLE ABSORPTION PANEL S4 panel is an economical and easily cleanable sound absorber. The S4 panel is constructed from a 3 PCF fiberglass core completely encapsulated with a fiberglass reinforced, aluminized polyester film facing. S4 is available in 1" and 2" thicknesses and panel sizes up to 48" x 120". The S4 panel with aluminized (silver) facing can be used

in

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated MODEL FLS, FLSS & FTS INSTALLATION INSTRUCTIONS removable blocking element (pvc pipe) leveling bolt top plate vertical restraint jam nuts restraint bolt bottom plate element after pry apart

blocking leveling

KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. GEOMETRIC SOUND DIFFUSERS Geometric Diffusers are available in three finishes and a variety of sizes. White thermo-molded copolymer, standard. Painted, optional. Fabric-faced, optional. NRC: 0.10 to 0.30. Dimensions* – Width x Length x Depth. Radius (7) Offset Pyramidal (3) 2' x 2' x 5.25". WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. WOOD-FRAMED CEILING HANGER Secured to wood-frame construction (e.g., joists, trusses), ICW incorporates a one-inch (1") rated deflection spring in series with a neoprene cup to resiliently support one or KINETICS NOISE CONTROL Kinetics Noise Control produces the industry’s largest selection of products and solutions that control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. HARDSIDE | ACOUSTICAL PANELS HardSide is a traditional acoustical panel offering design versatility. A variety of shaped edges and panel thicknesses allow you to design for the desired appearance and acoustics. The perfect solution for many reverberant noise problems, HardSide delivers superior performance. The core of this panel is a 6-7 PCF fiberglass

board.

QUIETTILE | NOISE CONTROL CEILING TILE QuietTile starts with your choice of ACT then Kinetics adds sound damped-mass to produce a composite ceiling tile designed to reduce sound transmission through a lay-in ceiling. QuietTile noise control ceilings are installed in normal ceiling grid typically 9/16" (narrow) or 15/16". Tiles are typically 24" x 24" or 24" x 48", custom sizes

are

RIM | ROLLOUT ISOLATION MATERIAL RIM Concrete. RIM Wood. Home | Floors | Ceilings | Partitions | The Process | About | Rep Login. Products manufactured in the USA by Kinetics Noise Control

ULTRA QUIET SR

The supple qualities of Ultra Quiet SR Floorboard make it a best-in-class continuous underlayment versus the 5 to 20mm thick sound control mats that cannot provide the comforting and code-required noise reduction. Withstands live loads up to 1000 psf. Maintains strength even when wet. Cuts easily with standard construction knife. GEOMETRIC SOUND DIFFUSERS Geometric Diffusers are available in three finishes and a variety of sizes. White thermo-molded copolymer, standard. Painted, optional. Fabric-faced, optional. NRC: 0.10 to 0.30. Dimensions* – Width x Length x Depth. Radius (7) Offset Pyramidal (3) 2' x 2' x 5.25". WALLMAT | STUD WALL ISOLATION STRIP Stud Wall Isolation Strip. Kinetics Noise Control’s Wallmat resilient partition isolation pad is a custom molded fiber glass board which resiliently decouples a sound-rated partition from non-isolated structure. Isolation is maintained with the use of KAI which isolates fasteners. Apply Wallmat continuously along the bottom and top plates

of

ICW | WOOD-FRAME CEILING HANGER The hanger bracket aids installation as it holds the spring in place while fastening gypsum board. ICW’s channel clip fits a typical cold-rolled-channel grid system and allows for leveling. ICW also makes fire ratings easy. A single UL assembly number allows for use of MUTA | SPRING WIRE-TIE CEILING HANGER Spring Wire-Tie Ceiling Hanger Using wires to connect with both the upper deck and ceiling grid system, this full one-inch rated deflection spring hanger works in series with a neoprene element to resiliently support one or more layers of gypsum board. WOOD-FRAMED CEILING HANGER Secured to wood-frame construction (e.g., joists, trusses), ICW incorporates a one-inch (1") rated deflection spring in series with a neoprene cup to resiliently support one or INSTALLATION GUIDELINES Installation Guidelines. Scroll down or use the drop down menu below to locate and download Kinetics installation guidelines. All documents are formatted as Adobe PDF files. If you are unable to locate a specific document please contact us. ----------------- Floor-Mounted Vibration Isolators Suspended Vibration Isolation Bases, Rails and

Curbs

KINFLEX | FLEXIBLE CONNECTORS Flexible Piping Connectors. KINFLEX Flexible Connectors prevent stresses due to expansion and contraction, isolate against the transfer of noise and vibration, and compensate for misalignment. KINETICS NOISE CONTROL Kinetics Noise Control sells through a worldwide network of independent sales representatives. Using the menu below, select the location of your project to find your Kinetics representative. SELECT NOISE CONTROL TYPES. vibration isolation, seismic and wind restraint. floors, ceilings, and walls -

SR FLOORBOARD

Kinetics SR Floorboard is a unique sound underlayment material which substantially reduces sound transmission through hard surface floor

systems.

RESTRAINED SPRING VIBRATION ISOLATOR Kinetics FLS vertically restrained spring isolation mounts are recommended as a noise and vibration isolator for mechanical equipment located near critically quiet areas, when the equipment to be isolated has significant changes of weight during maintenance operations, and for equipment subjected to external forces or high wind loads. PICADO | ACOUSTICAL WOOD COLLECTION Picado is one of four distinctive patterns for sound absorption in The Acoustical Wood Collection. Alto. Picado. Sereno. TAD Revealed. These patterns enable designers to create beautiful auditoriums, atriums, conference rooms, courthouses, student centers or other areas where finished wood is desired and acoustical comfort is needed. NEOPRENE VIBRATION PADS Pads are available in 4", 6", or 9" (102, 152, 228 mm) squares with capacities from 400 to 9,700 lbs. (181 to 4400 kg), or in full 18" (457 mm) square sheets which can be cut or drilled to meet field requirements. Kinetics Model NP or NG Pads can be used to isolate noise, shock, and high frequency vibration produced by mechanical,

industrial

ISOMAX | SOUND ISOLATION CLIPS IsoMax clip resiliently secures common drywall furring channel Offering significantly higher STC values than drywall attached to resilient channel, IsoMax ensures that installers will not inadvertently screw through the “resilient” leg of the channel into the joist or stud. Patent No. 7,093,814. SEISMIC ROOFTOP PIPE STANDS Application. KSPS stands stabilize piping by hard-clamping the piping to an adjustable steel mounting plate on the stand. This connection provides the necessary support the piping needs to act as a stand-alone support/restraint component; when used in accordance with MSS SP-69 table 3. KSPS stands can be used inside a structure or on

the roof top.

ICC | DECK-SUSPENDED CEILING HANGER Deck-Suspended Ceiling Hanger. This full one-inch rated deflection spring hanger ships with a pre-load spacer which keeps the isolator rigid making initial gypsum board installation easier than wire-tying. After the weight of gypsum board compresses the spring, a minimum 11-inch airspace is created between the concrete deck and the isolated

* PRODUCTS

* DOWNLOADS

Corporate Brochure Submittal Drawings Installation Guidelines Specifications BIM | 3D | AUTOCAD Literature * FIND YOUR REP

* CONTACT

* LOGIN

Rep Tools Silencers

E-Business

*

MECHANICAL SYSTEMS

AIRFLOW, VIBRATION, AND SEISMIC CONTROL NOISE AND VIBRATION FROM BUILDING MECHANICAL, ELECTRICAL, AND

PLUMBING SYSTEMS

Vibration Isolation Seismic and Wind Restraint Duct Silencers and Acoustic Louvers Enclosures and Barrier Walls Control noise and vibration from building mechanical, electrical, and

plumbing systems

Vibration Isolation Seismic and Wind Restraint Duct Silencers and Acoustic Louvers Enclosures and Barrier Walls FLOORS, CEILINGS, AND PARTITIONS

_CREATE QUIET_

ROOM ACOUSTICS

_IMPROVE SOUND_

INDUSTRIAL AND ENVIRONMENTAL NOISE AND VIBRATION CONTROL COMPLY WITH MUNICIPAL NOISE ORDINANCES, CONFORM TO OSHA STANDARDS, OR ACHIEVE OCCUPANT COMFORT Industrial Noise Control Environmental Noise Control Comply with municipal noise ordinances, conform to OSHA standards, or achieve occupant comfort Industrial Noise Control Environmental Noise Control HOME AND HOME THEATER RESIDENTIAL ACOUSTICS CONTROL ROOM-TO-ROOM NOISE AND IMPROVE THE QUALITY OF SOUND IN HOME

ENVIRONMENTS

Noise Control Sound Treatment Control room-to-room noise and improve the quality of sound in home

environments

Noise Control Sound Treatment SPECIALIZED APPLICATIONS CUSTOMIZED SOLUTIONS

DISCOVER

* IN CURB ACOUSTICAL TREATMENTS * Kinetics in curb acoustical treatments to control breakout noise from rooftop equipment fans and compressors into the space below. * CHILLER NOISE SOLUTIONS * Kinetics sound absorption solutions reduce the adverse reverberant effect caused by chillers and other mechanical equipment.

EVENTS

* AHR EXPO

* Booth 4160

* February 3-5, 2020

* Orlando, FL

JOB OPENINGS (3):

JOB TITLE

LOCATION

ACOUSTIC & VIBRATION ISOLATION MATERIALS ENGINEER

Columbus, OH

ENTRY LEVEL ACCOUNTING CLERK

Dublin, OH

TECHNICAL SALES ASSOCIATE

Columbus, OH

* About

* Company

* Projects

* Engineering

* Memberships

* Downloads

* Submittal Drawings * Installation Guidelines

* Specifications

* BIM | 3D | AutoCAD

* Literature

* Resources

* Find Your Rep

* Acoustical Consultants Listing * STC/IIC Sound Tests * Seismic Design Manual * Pipe & Duct Design Manual

* Login

* Rep Tools

* Silencers Online

* E-Business Portal

COMPANY OVERVIEW

Kinetics Noise Control, Inc. has extensive experience designing and manufacturing innovative products to control noise and vibration. Established in 1958 as industrial consultants focused on controlling sound and vibration, Kinetics now produces the industry’s largest selection of innovative products and solutions to control airborne noise, isolate structure-borne vibration, enhance room acoustics, create quiet spaces, and restrain non-structural building systems. Kinetics features an experienced staff of professional engineers, customer support, and sales representatives worldwide who are ready to

work with you.

Products manufactured in the USA by Kinetics Noise Control � 2019, Kinetics Noise Control, Inc.

PRODUCTS

DOWNLOADS

Submittal Drawings

Installation Guidelines Specifications BIM | 3D | AutoCAD Literature

FIND YOUR REP

CONTACT KINETICS

* 1-877-457-2695

* sales@kineticsnoise.com

LOGIN

Rep Tools Silencers

E-Business

$H1

$hl

X