HOW TO MEND IT

Search howtomendit.com for free help and advice. MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. HOW CAN I FIX MY TEFAL ACTIFRY? = ANSWERED If loose tighten with pliers and put back on the pcb. Fixed. dave manners. November 2013. take off lid and take out bowl.Take the fan cover off at the back. take out 3 screws underneath, then take the white cover off. the spindle will then take spindle out. sharon. July 2012. I can answer this question JOHN DEERE L130 MOWER WONT CLIMB HILL? = ANSWERED I know that the L130 is. not your father's John Deer, but it still cost $2500, which is more than most of the competitors models. that last much longer. My 12 year oms Craftsman with. a 20 hp Kholer and 48 in deck cuts and climbs much better than my 4 year old L 130. HOW DO I DIAGNOSE A WON'T LIFT PROBLEM WITH DAVID BROWN How do I diagnose a won't lift problem with David Brown 990 Hydraulic lift? My David Brown 990 tractor is refusing to raise the 3 Pt hitch. The time before when I used it the hydraulics whined a little but did eventually lift full height. WHAY IS THE FUEL MIXTURE FOR A HOMELITE SUPER 2 CHAINSAW Whay is the fuel mixture for a Homelite Super 2 chainsaw? Can you tell me what is the fuel mixture ratio for a Super 2 Homelite chainsaw Model#10454or 104544,serial#781290329 also what is the air gap setting for the magneto and the flyweel on this model.Thank you KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Kenmore sewing machine will no longer back stitch. Model #385.1695180? When I push the lever to get it to back stitch, it just continues to

go forward.

HOW TO MEND IT

Search howtomendit.com for free help and advice. MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. HOW CAN I FIX MY TEFAL ACTIFRY? = ANSWERED If loose tighten with pliers and put back on the pcb. Fixed. dave manners. November 2013. take off lid and take out bowl.Take the fan cover off at the back. take out 3 screws underneath, then take the white cover off. the spindle will then take spindle out. sharon. July 2012. I can answer this question JOHN DEERE L130 MOWER WONT CLIMB HILL? = ANSWERED I know that the L130 is. not your father's John Deer, but it still cost $2500, which is more than most of the competitors models. that last much longer. My 12 year oms Craftsman with. a 20 hp Kholer and 48 in deck cuts and climbs much better than my 4 year old L 130. HOW DO I DIAGNOSE A WON'T LIFT PROBLEM WITH DAVID BROWN How do I diagnose a won't lift problem with David Brown 990 Hydraulic lift? My David Brown 990 tractor is refusing to raise the 3 Pt hitch. The time before when I used it the hydraulics whined a little but did eventually lift full height. WHAY IS THE FUEL MIXTURE FOR A HOMELITE SUPER 2 CHAINSAW Whay is the fuel mixture for a Homelite Super 2 chainsaw? Can you tell me what is the fuel mixture ratio for a Super 2 Homelite chainsaw Model#10454or 104544,serial#781290329 also what is the air gap setting for the magneto and the flyweel on this model.Thank you KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Kenmore sewing machine will no longer back stitch. Model #385.1695180? When I push the lever to get it to back stitch, it just continues to

go forward.

HOW TO MEND CORRECT CODES Today DeLonghi bean to cup. ESAM22XY infuser stuck? DeLonghi ESAM22XY Infuser stuck down with drip tray in. Door will not close and tray

cannot be removed.

HOW TO MEND LOCATED FUSE BONNET Today DeLonghi bean to cup. ESAM22XY infuser stuck? DeLonghi ESAM22XY Infuser stuck down with drip tray in. Door will not close and tray

cannot be removed.

HOW TO MEND BOILER FAULTY Today How can I mend Hayter 41 Quantum blade not turning? I have a Hayter 41 Quantum and there are two issues:- The first is that the blade has stopped turning. ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

MY COUNTAX WILL NOT START? = ANSWERED If there is no click at all when switching from RUN to START, then either the solenoid is duff (test for battery voltage on the trigger wire when at START), or there is a faulty interlock switch somewhere preventing the engne from cranking. Usual culprit is the brake switch. If this is a model with electric deck lift etc, then either one or

SDS DRILL CHUCK

Mike. July 2014. 1 pull out the bit as far as it goes and grease the bit of shaft that you see. 2 push in the bit, turn the drill on to chisel only setting. 3 stand the drill on its handle with the bit pointing to the sky. 4 turn on the drill grab the bit and push it in till you feel it doing the hammer action. KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Take the cover off the top with two screws, then remove bottom with several screws, then remove the side cover. This allows you to loosen the screws (right side and top of plate) to take off the front cover of the machine surrounding the reverse lever. MY BATTERY OPERATED WALL CLOCK HANDS WON'T MOVE August 2008. Clocks and Watches, Wall Clocks Clock Wont Move. (1) Check whether any dirt in between the plastic gears of the clock mechamism. This you have to carefully open the cover of the clock mechanism. Made sure you know how to fix it back all those gears. (2) If all the gears are alright, then probably the small capacitor in it

is faulty.

SQUEAKY ROLLER BLINDS? = ANSWERED Looks like the makers of silicone spray will do well for a while! Alison. November 2008. This can be alleviated by spraying silicone spray right into the mechanism area. Make sure you shield the fabric of the roller blind to avoid staining the fabric. (available from art shops, stationers, haberdashery shops, John Lewis). Marian Forrest. H98 FAULT ON PANASONIC INVERTER 1200W HIGH POWER MICROWAVE Usually indicates a problem with the magnetron or the High Voltage power supply (Inverter). Because of the amount of voltage involved and the complexity & expense of the parts involved, the repair is best left to an experienced technican.

HOW TO MEND IT

Search howtomendit.com for free help and advice. HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. START SWITCH PROBLEM? = ANSWERED Morphy Richards Household Appliances, Vacuum Cleaners Start Switch Problem. I have a cordless vac for 18 monthes and it has started to work intermittently then stop !! unable to get to the brushes for the immovable battery pack!!! assuming its another " timed to go burn out

"

FUEL MIX FOR MCCULLOCH PETROL GRASS TRIMMER? = ANSWERED September 2008. McCulloch Garden Tools, Grass Trimmers Fuel Mix Mcculloch. The ratio is 40/1 it's on the fuel cap. Crawford. September 2013. Consult the recommended dilution ratio on the bottle of two stroke oil you are going to use. Always dilute at that ratio and you won't have any problems. The manufacturer will recommend a ratio, but

this

MY COUNTAX WILL NOT START? = ANSWERED If there is no click at all when switching from RUN to START, then either the solenoid is duff (test for battery voltage on the trigger wire when at START), or there is a faulty interlock switch somewhere preventing the engne from cranking. Usual culprit is the brake switch. If this is a model with electric deck lift etc, then either one or STUCK (OPEN) VELUX WINDOW? = ANSWERED John Tucker. July 2014. There is more help available. Mend - stuck, open, window. Need to mend your Velux windows and door? Check and tighten the torx screw that holds the frame, located where the spring attaches to the bottom of sliding hinge. If it has loosened It can catch and stop the hinge from sliding. CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012

HOW TO MEND IT

Search howtomendit.com for free help and advice. HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. START SWITCH PROBLEM? = ANSWERED Morphy Richards Household Appliances, Vacuum Cleaners Start Switch Problem. I have a cordless vac for 18 monthes and it has started to work intermittently then stop !! unable to get to the brushes for the immovable battery pack!!! assuming its another " timed to go burn out

"

FUEL MIX FOR MCCULLOCH PETROL GRASS TRIMMER? = ANSWERED September 2008. McCulloch Garden Tools, Grass Trimmers Fuel Mix Mcculloch. The ratio is 40/1 it's on the fuel cap. Crawford. September 2013. Consult the recommended dilution ratio on the bottle of two stroke oil you are going to use. Always dilute at that ratio and you won't have any problems. The manufacturer will recommend a ratio, but

this

MY COUNTAX WILL NOT START? = ANSWERED If there is no click at all when switching from RUN to START, then either the solenoid is duff (test for battery voltage on the trigger wire when at START), or there is a faulty interlock switch somewhere preventing the engne from cranking. Usual culprit is the brake switch. If this is a model with electric deck lift etc, then either one or STUCK (OPEN) VELUX WINDOW? = ANSWERED John Tucker. July 2014. There is more help available. Mend - stuck, open, window. Need to mend your Velux windows and door? Check and tighten the torx screw that holds the frame, located where the spring attaches to the bottom of sliding hinge. If it has loosened It can catch and stop the hinge from sliding. CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 HOW TO MEND CORRECT CODES Today DeLonghi bean to cup. ESAM22XY infuser stuck? DeLonghi ESAM22XY Infuser stuck down with drip tray in. Door will not close and tray

cannot be removed.

HOW TO MEND LOCATED FUSE BONNET Today DeLonghi bean to cup. ESAM22XY infuser stuck? DeLonghi ESAM22XY Infuser stuck down with drip tray in. Door will not close and tray

cannot be removed.

HOW TO MEND BOILER FAULTY Today How can I mend Hayter 41 Quantum blade not turning? I have a Hayter 41 Quantum and there are two issues:- The first is that the blade has stopped turning. HOW TO MEND POWER DEVIL Today Cannot start my Hayter 13/30 ride on mower? Cannot start my Hayter 13/30 ride on mower. All of a sudden it won't start. I replaced the plugs and ignition HOW TO MEND RUSSELL HOBBS KETTLE My Russell Hobbs quiet boil kettle keeps switching itself on and off when boiling and also 'sticks' in its bas Pages 6 5 4 3 2. Replacing my DUALIT power adapter (SA110C-12BS-I? HOW TO MEND CORBY TROUSER PRESS 4400 My Corby Trouser Press 4400 is not heating up to press the trousers, all the lights come on an the timer works STUCK (OPEN) VELUX WINDOW? = ANSWERED John Tucker. July 2014. There is more help available. Mend - stuck, open, window. Need to mend your Velux windows and door? Check and tighten the torx screw that holds the frame, located where the spring attaches to the bottom of sliding hinge. If it has loosened It can catch and stop the hinge from sliding. MY TOASTER KEEPS TRIPPING THE ELECTRIC? = ANSWERED You need to (a) shake all the crumbs out of the toaster, then (b) see if that has fixed the problem. (c) If the toaster still fuses, then (d) unplug it (very important for safety) and take it to a well-lit position (best lighting is outdoors on a day with hazy sun or a translucent white cloud covering most of the sky). ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

HOW TO MEND IT

Search howtomendit.com for free help and advice. KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Kenmore sewing machine will no longer back stitch. Model #385.1695180? When I push the lever to get it to back stitch, it just continues to

go forward.

HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. HOW CAN I FIX MY TEFAL ACTIFRY? = ANSWERED If loose tighten with pliers and put back on the pcb. Fixed. dave manners. November 2013. take off lid and take out bowl.Take the fan cover off at the back. take out 3 screws underneath, then take the white cover off. the spindle will then take spindle out. sharon. July 2012. I can answer this question WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

HOW CAN I FIX FLYMO THAT'S SMOKING AND MOTOR RUNNING VERY how can i fix flymo that's smoking and motor running very slow? Cutting the grass today my flymo's motor and blade started turning over very slow, eventually stopping and JOHN DEERE L130 MOWER WONT CLIMB HILL? = ANSWERED I know that the L130 is. not your father's John Deer, but it still cost $2500, which is more than most of the competitors models. that last much longer. My 12 year oms Craftsman with. a 20 hp Kholer and 48 in deck cuts and climbs much better than my 4 year old L 130. HOW CAN I REMOVE SPEED RESTRICTOR ON MY FORD TRANSIT Fast adz. May 2012. go to fuse box in glove box go to 3rd fuse along from left then 1 down have engine running, put foot on brake and remove fuse keep foot on brake untill on dash readout you see ENGINE MALFUNCTION then take foot of brake put fuse back in then press brake again untill ENGINE MALFUNCTION goes off then restriction is lifted.

curt.

HOW TO MEND IT

Search howtomendit.com for free help and advice. KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Take the cover off the top with two screws, then remove bottom with several screws, then remove the side cover. This allows you to loosen the screws (right side and top of plate) to take off the front cover of the machine surrounding the reverse lever. HOW CAN I REPLACE MY ELECTRA LITE 9 WEEDEATER STRING July 2010. how can I replace my electra lite 9 weedeater string? daniel boda. July 2010. Pull straight away from the body of the trimmer. The spool is on clips. Remember, when replacing the spool to retain tension on the string as you reinstall the spool. Otherwise, it will get knotted up before you use it ;) HOW CAN I FIX MY TEFAL ACTIFRY? = ANSWERED If loose tighten with pliers and put back on the pcb. Fixed. dave manners. November 2013. take off lid and take out bowl.Take the fan cover off at the back. take out 3 screws underneath, then take the white cover off. the spindle will then take spindle out. sharon. July 2012. I can answer this question HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. WHY DOES MY LAMINATE FLOOR SNAP CRACKLE AND POP Rob S. November 2011. The most simple cause is the laying of the flooring was not pressed down properly during fitting so air bubbles are coming through the surface of the floor and adhesive. ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

HOW TO MEND BOILER FAULTY Today How can I mend Hayter 41 Quantum blade not turning? I have a Hayter 41 Quantum and there are two issues:- The first is that the blade has stopped turning. HOW DO YOU PUT THE BACK OF A WATCH BACK ON? = ANSWERED Position back cover on watch. Screw down C-clamp until it makes contact. Make sure everything is still lined up before applying pressure. Gradually tighten C-clamp until the back clicks into place. James. December 2012. I tried the freezer tick and it didn't work for

me.

WHY DOES MY STRIMMER BACKFIRE AND CUT OUT? = ANSWERED There is more help available. Mend - strimmer, cut, out. could be the exhaust, a blown exhaust gasket allows air into the exhaust which allows any unburnt fuel to ignite, which it will at these temperatures, i.e. a backfire. also, check the plug and spark gap, the most likely cause of misiring. beat the plug contacts into submission

with a wire

MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

MOWER BLADES ROUND HOLE ,STAR HOLE? They sent me the right size ,the right hole dia. and the right spacing of the 3 holes. But,the center hole is round,whereas my old blades have a star shape hole.Is there any way I can use them ? I was thinking maybe a lock washer. Sending them back is not an option. Thank you. Bob. February 2009. Garden Tools, Lawn Mowers Mower Blades

Round Star.

ELECTRIC LAWN MOWER OVERHEATS & CUTS OUT? = ANSWERED electric lawn mower overheats & cuts out? Hi, I recently dusted off my flymo electric lawn mower and attempted to cut my overgrown front garden, after about 10 minutes I spelt a burning smell and the motor sounded like it was struggling so I unplugged it and turned it over. CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 WHERE IS THE ERASE PROTECTION TAB ON A VHS TAPE Argh. April 2008. If you look on the back of the tape on the left hand side is a little square hole with a piece of plastic in it,snap it off with a screwdriver or knife,if you want to tape over the tape again stick a piece of sellotape over the hole. Rich. March 2008. WHAY IS THE FUEL MIXTURE FOR A HOMELITE SUPER 2 CHAINSAW Whay is the fuel mixture for a Homelite Super 2 chainsaw? Can you tell me what is the fuel mixture ratio for a Super 2 Homelite chainsaw Model#10454or 104544,serial#781290329 also what is the air gap setting for the magneto and the flyweel on this model.Thank you HOMELITE CHAIN SAW WON'T IDLE? = ANSWERED Homelite chain saw won't idle? This saw is hard to start, I've cleaned the fuel filter, replaced the fuel lines, choke the saw pull till exhausted, let sit for a while ,place choke at half, pul an it might start, I think the adjustment are out of whack, What is the procedure for adjustment,screw all the way in on fuel,air mixture an back out one an a half turn on each or what? i've tried ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWERED Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 HOW DO I DIAGNOSE A WON'T LIFT PROBLEM WITH DAVID BROWN How do I diagnose a won't lift problem with David Brown 990 Hydraulic lift? My David Brown 990 tractor is refusing to raise the 3 Pt hitch. The time before when I used it the hydraulics whined a little but did eventually lift full height. SQUEAKY ROLLER BLINDS? = ANSWERED Looks like the makers of silicone spray will do well for a while! Alison. November 2008. This can be alleviated by spraying silicone spray right into the mechanism area. Make sure you shield the fabric of the roller blind to avoid staining the fabric. (available from art shops, stationers, haberdashery shops, John Lewis). Marian Forrest. ANTI-FLOOD DEVICE ON A AEG DISHWASHER? = ANSWERED Anti-Flood device on a AEG Dishwasher? Have an older AEG Model 420 dishwasher. Avice on how to reset the anti-flood device please. Have cleared all waste pipe and filter blockages now but pump runs all the

time and no water.

HOW CAN I STOP THE BEEPING IN KITCHENAID KSCS25INSS Had similar issue with our liebherr american style fridge and quite a few companies round to look at it which they all did still didnt work got lucky in the end when i got in touch with www.agsrefrigeration.co.uk a company who service the london and surrey area they came out and found that we had a faulty wiring connection am very glad to say all is working like its supposed to do. KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODEL Kenmore sewing machine will no longer back stitch. Model #385.1695180? When I push the lever to get it to back stitch, it just continues to

go forward.

WHERE IS THE ERASE PROTECTION TAB ON A VHS TAPE Argh. April 2008. If you look on the back of the tape on the left hand side is a little square hole with a piece of plastic in it,snap it off with a screwdriver or knife,if you want to tape over the tape again stick a piece of sellotape over the hole. Rich. March 2008.

HOW TO MEND IT

Search howtomendit.com for free help and advice. HOW TO MEND PROJECTION LIGHT BLINKS i have a 50ux52b projection tv and the power light blinks and goes when plu? i have a 50ux52b projection tv and the power light in front blinks and the green indicator lights on the circu HOW TO MEND PROBLEM PHONE CONNECTION Search howtomendit.com for free help and advice. HOW TO MEND SOVEREIGN ROTARY MOWER Search howtomendit.com for free help and advice. WHY DOES MY STRIMMER BACKFIRE AND CUT OUT? = ANSWERED There is more help available. Mend - strimmer, cut, out. could be the exhaust, a blown exhaust gasket allows air into the exhaust which allows any unburnt fuel to ignite, which it will at these temperatures, i.e. a backfire. also, check the plug and spark gap, the most likely cause of misiring. beat the plug contacts into submission

with a wire

MY TOASTER KEEPS TRIPPING THE ELECTRIC? = ANSWERED You need to (a) shake all the crumbs out of the toaster, then (b) see if that has fixed the problem. (c) If the toaster still fuses, then (d) unplug it (very important for safety) and take it to a well-lit position (best lighting is outdoors on a day with hazy sun or a translucent white cloud covering most of the sky).

HOW TO MEND CITROEN

Request for user manual? Does anyone have access to the user manual for a wired Security Master alarm. Possible the TP-800. HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. HOW CAN I STOP THE BEEPING IN KITCHENAID KSCS25INSS Had similar issue with our liebherr american style fridge and quite a few companies round to look at it which they all did still didnt work got lucky in the end when i got in touch with www.agsrefrigeration.co.uk a company who service the london and surrey area they came out and found that we had a faulty wiring connection am very glad to say all is working like its supposed to do. WHY IS MY DISHWASHER USING SO MUCH SALT? = ANSWERED March 2014. Neff Kitchen Appliances, Dishwashers Dishwasher Much Salt. Just check the salt cap is not split and that it is on squarely and is sealing tight, if all this is ok then the salt valve is probably stuck on. Salt valve is on left side of machine bottom of plastic water jacket. If you are not in hard water area you don't need salt. Kenjo. ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWEREDE1 ERROR CODE ON TREADMILLE1 ERROR CODE ON TREADMILLHORIZON T101 E1 ERROR CODEHORIZON T101 E1 ERROR CODELIFESPAN TREADMILL E1LIFESPAN TREADMILL E1 ERROR

CODE

Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900MAGNETEK CONVERTER CHARGER 900 SERIESMAGNETEK POWER CONVERTERMAGNETEK CONVERTER TROUBLESHOOTINGMAGNETEK POWER CONVERTER REPLACEMENTMAGNETEK 900 SERIES CONVERTER TROUBLESHO…MAGNETEK SERIES 900 MODEL 950 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 HOW DO I DIAGNOSE A WON'T LIFT PROBLEM WITH DAVID BROWN How do I diagnose a won't lift problem with David Brown 990 Hydraulic lift? My David Brown 990 tractor is refusing to raise the 3 Pt hitch. The time before when I used it the hydraulics whined a little but did eventually lift full height. ERROR MESSAGE E1 STALL ON TRUE TREADMILL? = ANSWEREDE1 ERROR CODE ON TREADMILLE1 ERROR CODE ON TREADMILLHORIZON T101 E1 ERROR CODEHORIZON T101 E1 ERROR CODELIFESPAN TREADMILL E1LIFESPAN TREADMILL E1 ERROR

CODE

Stuart May. July 2009. E1 Stall means the incline motor is not responding for some reason. It could be the incline limit switch, the PC board, or the wire from the switch to the PC board. Unplug the treadmill, let it sit long enough to drain the capacitors, then crank the screw down to level the machine. Inspect the limit switch and

wiring to it.

TOYOTA HIACE POWERVAN SUMP REPLACEMENT? Toyota Hiace Powervan sump replacement? What is the procedure to replace the sump on a Hiace Powervan 2400cc? Is it a difficult job? Can it be done with the MY TASSIMO IS LEAKING FROM THE BOTTOM ? = ANSWERED Bosch Tassimo Kitchen Appliances, Coffee Machines. Go to ACE hardware get a small O ring and place it on the beveled plastic filler spout at the bottom of the water container put a small amount of clear gasket sealer or vaseline around the beveled plastic filler spout. Joe.

September 2013.

CAN I REPLACE MY MAGNETEK CHARGER CONVERTER? SERIES 900MAGNETEK CONVERTER CHARGER 900 SERIESMAGNETEK POWER CONVERTERMAGNETEK CONVERTER TROUBLESHOOTINGMAGNETEK POWER CONVERTER REPLACEMENTMAGNETEK 900 SERIES CONVERTER TROUBLESHO…MAGNETEK SERIES 900 MODEL 950 can i change the converter charger series 900 nodel 940.2 to something else al leduc June 2012 HOW DO I DIAGNOSE A WON'T LIFT PROBLEM WITH DAVID BROWN How do I diagnose a won't lift problem with David Brown 990 Hydraulic lift? My David Brown 990 tractor is refusing to raise the 3 Pt hitch. The time before when I used it the hydraulics whined a little but did eventually lift full height. SQUEAKY ROLLER BLINDS? = ANSWERED Looks like the makers of silicone spray will do well for a while! Alison. November 2008. This can be alleviated by spraying silicone spray right into the mechanism area. Make sure you shield the fabric of the roller blind to avoid staining the fabric. (available from art shops, stationers, haberdashery shops, John Lewis). Marian Forrest. ANTI-FLOOD DEVICE ON A AEG DISHWASHER? = ANSWERED Anti-Flood device on a AEG Dishwasher? Have an older AEG Model 420 dishwasher. Avice on how to reset the anti-flood device please. Have cleared all waste pipe and filter blockages now but pump runs all the

time and no water.

HOW CAN I STOP THE BEEPING IN KITCHENAID KSCS25INSS Had similar issue with our liebherr american style fridge and quite a few companies round to look at it which they all did still didnt work got lucky in the end when i got in touch with www.agsrefrigeration.co.uk a company who service the london and surrey area they came out and found that we had a faulty wiring connection am very glad to say all is working like its supposed to do. KENMORE SEWING MACHINE WILL NO LONGER BACK STITCH. MODELKENMORE SEWING MACHINE MANUALSKENMORE SEWING MACHINE MODELS LISTKENMORE SEWING

MACHINES FOR SALE

Kenmore sewing machine will no longer back stitch. Model #385.1695180? When I push the lever to get it to back stitch, it just continues to

go forward.

WHERE IS THE ERASE PROTECTION TAB ON A VHS TAPE Argh. April 2008. If you look on the back of the tape on the left hand side is a little square hole with a piece of plastic in it,snap it off with a screwdriver or knife,if you want to tape over the tape again stick a piece of sellotape over the hole. Rich. March 2008.

HOW TO MEND IT

Search howtomendit.com for free help and advice. HOW TO MEND PROJECTION LIGHT BLINKS i have a 50ux52b projection tv and the power light blinks and goes when plu? i have a 50ux52b projection tv and the power light in front blinks and the green indicator lights on the circu HOW TO MEND PROBLEM PHONE CONNECTION Search howtomendit.com for free help and advice. HOW TO MEND SOVEREIGN ROTARY MOWER Search howtomendit.com for free help and advice. WHY DOES MY STRIMMER BACKFIRE AND CUT OUT? = ANSWERED There is more help available. Mend - strimmer, cut, out. could be the exhaust, a blown exhaust gasket allows air into the exhaust which allows any unburnt fuel to ignite, which it will at these temperatures, i.e. a backfire. also, check the plug and spark gap, the most likely cause of misiring. beat the plug contacts into submission

with a wire

MY TOASTER KEEPS TRIPPING THE ELECTRIC? = ANSWERED You need to (a) shake all the crumbs out of the toaster, then (b) see if that has fixed the problem. (c) If the toaster still fuses, then (d) unplug it (very important for safety) and take it to a well-lit position (best lighting is outdoors on a day with hazy sun or a translucent white cloud covering most of the sky).

HOW TO MEND CITROEN

Request for user manual? Does anyone have access to the user manual for a wired Security Master alarm. Possible the TP-800. HOW TO REPAIR PIN HOLE LEAK IN KITCHEN FAUCET SPOUT D.I.Y, Plumbing. The following method is 100% guaranteed to work and it costs you next to nothing. Now give me a good tip . hahahaJust kidding. Ok, back to the subject, how to fix a pin hole on the faucet spout? If you don't mind the looks, you can wrap a wide rubber band around the pin hole couple of times. HOW CAN I STOP THE BEEPING IN KITCHENAID KSCS25INSS Had similar issue with our liebherr american style fridge and quite a few companies round to look at it which they all did still didnt work got lucky in the end when i got in touch with www.agsrefrigeration.co.uk a company who service the london and surrey area they came out and found that we had a faulty wiring connection am very glad to say all is working like its supposed to do. WHY IS MY DISHWASHER USING SO MUCH SALT? = ANSWERED March 2014. Neff Kitchen Appliances, Dishwashers Dishwasher Much Salt. Just check the salt cap is not split and that it is on squarely and is sealing tight, if all this is ok then the salt valve is probably stuck on. Salt valve is on left side of machine bottom of plastic water jacket. If you are not in hard water area you don't need salt. Kenjo. Ask Question Search Categories

☰

__ __

Search

Home Ask Question Search Categories Most Recent Unanswered Help

HOWTOMENDIT.COM

Find out how to mend vacuum cleaners and mobile phones, cars and DVD players, computers and tumble dryers, televisions and motorbikes, CD players and washing machines. When we say "find out how to mend just about anything" we mean it! -------------------------

__ Categories

FREE REPAIR HELP AND INFORMATION HOWTOMENDIT.COM find out how to mend just about anything. -------------------------

__ Categories

How do I repair my Alcatel? How do I mend my Optima OPH616? How do I mend my JCB 2CX? How do I mend my Sunbeam?

POPULAR CATEGORIES

CARS

HEATING/BOILERS

WASHING MACHINES

__ BRAND NEW QUESTIONS How can I mend my ...

Today

AQUASONCI 4 RUNS COLD? aquasonic 4 shower heater runs cold

Today

POLITICAL 2400 VAPORETTO? I pull the wire of my vaporetto too much and now it is not working. How can I open and join the wires back i...

Recent

RATTLING SLIDING DOOR? Rattling sliding door on Renault Trafic 2014 new style

Recent

PAPER EMPTY CODE WILL NOT CLEAR ER A420? Changed paper in our ER a420 cash register and pressed cl. it will not clear and keeps saying paper empty. We ...

Recent

MOUNTFIELD 1228H IGNITION CONNECTORS IN WHICH ORDER? Mountfield 1228H ignition switch I'm having trouble

Recent

MORPHY RICHARDS 48474 HAND BLENDER? My Morphy Richards hand held blender just stopped working, can I mend

it?

Recent

TRACKING AND TENSIONING ON A POWER CRAFT BANDSAW? Can someone please tell me if there is a parts breakdown diagram for a Power craft MIA190 bandsaw blade tracki...

Retune old tv?

Asus C523NA-EJ0178 Chromebook won't turn on? Vauxhall Antara alarm? Direction indicators flashing too fast? How to fix F4 problem on condenser dryer? Fix e001 on akinto ad-3190?

ASK QUESTION

Do you need free help? Ask your

question.

HOWTOMENDIT.COM for free repair help, information and advice. -------------------------

__ Ask Question

How can I repair my appliance? How can I make my toilet flush properly? How can I fix my Olympia Cash Register? How can I fix my Suffolk Punch?

CAN YOU HELP?

Are you an expert who can help answer questions? Click here to see the unanswered questions for each category.

POPULAR

__ Fix a tumble dryer __ Service your car __ Mend a vacuum __ Repair a mower __ Fix my dishwasher __

Mend your TV

__

Attempting repairs can be dangerous. In many instances work should only be undertaken by a qualified professional. See Terms and Conditions .

�2003-2021

__

PRIVACY

howtomendit.com uses cookies to ensure that you get the best experience using our website. Learn more.